Antique Repairs and Restorations

Repairs ... We love 'em ... If they could only talk; then they'd be even more interesting .... This pair of tables came in one at a time with the idea that we only had to put a leg back on one of them and patch a broken corner. However, they came in with a bureau that was a basket case when it arrived and looked like a million bucks when it left .... We fixed and delivered that piece first and when the client saw how her bureau had been transformed, she sent us the mate to the table above with instructions to tune them up and refinish the tops, which had suffered some serious damages over the years. So, as we worked with them, we dreamed up their story ... Who knows? Here's what we think..... Click the pictures to enlarge them as we go ...

Here's the bureau ... When it came to us, it looked like it had been in a barn for quite a while ... The drawer supports had all collapsed and the drawers didn't run, more than half of the base was off, the moldings were flapping ... Backboards were missing ... Will did a good job getting it all back together. It took a few hours, but it was definitely worth doing ... When it left, it looked great. Here's the deal on the tables ...

The builder was a skilled craftsmen. The inlays are nicely done, the veneers on the aprons appear to be hand sawn, and the tops of the pair of tables are pairs of bookmatched boards, 1,2,3 center middle outside ... The boards match .... not an accident .

We opted for scraping rather then stripping ... We find when we strip we always have to do a lot of sanding and that kills some of the handmadeness of the surfaces ... scraping's better in our opinion if you can do it ... The finish was not original and it was thin and flaky and actually shot off the front edge of the scraper as I worked.

After we got the leg back on there were about 10 places on the aprons and drawer faces that needed patching or regluing ... The aprons were bricklaid in about 6 layers and then veneered with the grain vertical . The red arrow shows a leg reinforced with a pair of hinges !! We left them there. They worked and you have to honor the history ...

We patched in a bunch of missing pieces and recolored them to match

Here's an interesting thing .... The legs were all cut at the point where the arrow is and the legs that are below that point on the tables now have a different finish and are held on by short half inch diameter dowels (we know cause they wiggle and we fixed one that was broken off) and in some cases hinges ... It also looks like the detail that is on the legs at one time was also on the aprons and drawer fronts.

One had a broken corner and a rotten spot that needed patching

Luckily I had a piece of crotch walnut with similar figure to make a patch

All in, all done ... and ready for the next 50 years or so ...

Another Interesting Repair

We fixed a desk for the niece of one of our longtime customers recently. It was her grandmother's desk, and one of it's legs had been broken (and repaired) several times. She had moved to a new house and could no longer prop it in the corner as she had in the past. It was a cool piece with nice carvings, some slick hardware that pushed out the flap supports when you pulled open the desk front, and onyx drawer faces and gallery details inside. It took some creative gluing and clamping to reattach the carved foot but it looked pretty good when it was done, if I do say so myself ... Click the photos to enlarge them ...

Badly repaired break

planed the ends smooth

Figured out how much was missing

We screwed a piece of plywood to the other three legs to locate the broken foot contact and put a temporary leg the right length in place so that when the leg was fixed, the desk would sit level.

Finished the joinery , doweled it as it was and glued it up with the broken foot

Rough shaped it

Did some minimal suggestive carving

Opened it up and found we needed to get rid of the blotter paper that was taped in there and get some leather down.

Stretched a piece of leather over some scrap plywood, made a luan ply pattern and cut the leather to exact size. masked off the desk and sprayed 3M Spray 90 adhesive on the leather and the desk insert. We put a piece of wax paper under most of the leather and slowly pressed the leather down and tugged the wax paper along, stretching the leather as we pushed it ( glued it ) into place. In the end, the width was good but we had to trim about 1'4" off the length in place.

There were some sweet onyx drawer faces that needed some refitting and handle reattachment and the two columns in the center were 'secret' compartments ... Loved the whole thing when it was done and so did the client when we dropped it off last week.